產品中心
?
C-EP 4619 Technical Data Sheet
Single component epoxy adhesive單組分環氧樹脂粘接劑
PRODUCT DESCRIPTION 產品介紹
C-EP 4619 is a One-component CSP/BGA corner bond fill material. It can be cured during lead-free solder reflow while allowing self-alignment of IC components. The material can be pre-applied to the board at the corners of the CSP pad site using a Standard SMA dispenser. When heat cured, it improves mechanical reliability of hand-held Devices. The material is reworkable. C-EP 4619是一種單組分CSP/BGA轉角粘接填充材料,它在無鉛回流焊接中固化的同時還能自動準直IC元件。使用標準的SMA(表面安裝粘接劑,貼片膠)分散方式,該材料可以預先施加到電路板上的CSP襯墊處的轉角位置。加熱固化后,該材料可提高手持設備的機械可靠性。C-EP 4619具可返修性。
PROPERTIES OF UNCURED MATERIAL 固化前材料性能
Properties 性能 |
Test Method 測試方法 |
C-EP 4619 |
Color/Appearance 顏色/外觀 |
Visual |
Liquid, Black 黑色液體 |
Specific Gravity 比重 |
ASTM D-792 |
1. 23 |
Viscosity 粘度@ 25°C, cps |
ASTM D-2393 |
50,000 |
TYPICAL PROPERTIES OF CURED MATERIAL 固化后材料典型物理性能
Material cured at 180°Cx3 hours 材料在180°C下固化3小時
Property 性能 |
Test Method 測試方法 |
Value 數值 |
Hardness 硬度(Shore D) |
ASTM D-2240 |
70 |
Flow rate, room temperature |
|
Good dispense capability |
Glass transition temperature 玻璃化轉變溫度, Tg, oC |
|
120 |
Coefficient of thermal expansion 熱膨脹系數CTE, ppm |
ASTM D3386 |
57/180 |
Strain at yield |
|
2.5 % |
Flexual modulus 模量, N/mm2 |
|
2100 |
Tensile Strength, MPa |
ASTM D790 |
55 |
Volume resistivity 體電阻系數, ohms-cm |
ASTM D-257 |
4.3 E+16 |
Surface resistivity 表面電阻, ohms |
ASTM D-257 |
8.4 E+16 |
Dielectric constant |
ASTM D150 |
3.5 (10 MHz) |
DIRECTIONS FOR USE使用指南
Resin/Hardener Ratio (by weight) 樹脂/固化劑(重量比) one component 單組分
Resin/Hardener Ratio (by volume) 樹脂/固化劑(體積比) one component 單組分
Pot Life, 25°C 使用期 3 months 3月
CURING SCHEDULE 固化進度表:
Lead-free reflow with 245°C . 在245°C下無鉛回流。
STORAGE INFORMATION 貯存方法
Store at 2 oC to 8 oC in a unopened can and dry condition. Shelf life is 6 months. 2 oC到8 oC 于干燥環境中密封保存, 保質期為6個月。