產品中心
?
C-EP 3125A/B Technical Data Sheet
HEAT/CHEMICAL-RESISTANT ADHESIVE KAN抗熱/化學侵蝕膠粘劑
PRODUCT DESCRIPTION 產品介紹
C-EP 3125 is a two-component, room-temperature curing paste adhesive of high strength and toughness. It is Thixotropic with good environmental and excellent chemical resistance. Used for bonding electronic components, GRP structures, and most other items where a higher than normal temperature or more aggressive environment is to be encountered in service. C-EP 3125 是一種雙組分，高強度和韌性的室溫固化糊狀膠粘劑。它具有很高的觸變性并且具有極佳的環境和化學侵蝕抵抗性。C-EP 3125在用于粘結電子元件，玻璃增強纖維塑料結構件和大多數其他組件中，將可抵抗更高的溫度和更惡劣的環境條件
APLLICATIONS 應用領域
-
Metals 金屬
-
Ceramics 陶瓷
-
GRP 玻璃纖維增強塑料
-
Electronic components 電子元件
ADVANTAGES 優點
-
Heat resistant to 248°F (120°C) 可抗120°C高溫
-
Very resistant to water and a wide variety of chemicals 對水和大多數化學物質具有好的抵抗性
-
Gap-filling, non-sagging up to 5mm thickness 縫隙填充，5mm厚沒有下垂
-
Good bonds to a wide variety of substrates 對大多數基質具有很好的粘結性
PROPERTIES OF UNCURED MATERIAL 固化前材料性能
|
Property 性能 |
Test Method 測試方法 |
Resin A |
Hardener B |
|
Color/Appearance 顏色/外觀 |
Visual |
Beige paste米色糊狀 |
Gray Thixotropic paste灰色觸變性膏狀 |
|
Specific Gravity 密度, g/cc, |
ASTM D-792 |
1.6 |
1.6 |
|
Viscosity 粘度, (cP), 25℃ |
ASTM D-2393 |
70,000 |
130,000 |
TYPICAL MIXED PROPERTIES 典型混合性能
|
Reaction Ratio (by weight) |
|
100R/50H |
|
Reaction Ratio (by volume) |
|
100R/50H |
|
Pot Life（100g） |
ASTM D-2471 |
40 minutes |
|
Mixed viscosity |
ASTM D-2393 |
90,000 cP |
RECOMMENDED CURE SCHEDULES
|
Temperature 固化溫度 |
Handling Strength 操作強度 |
Minimum Cure Time 最小固化時間 |
|
50oF (10oC) |
16 hours |
24 hours |
|
59o (15oC) |
9 hours |
11.5 hours |
|
77oF (25oC) |
3.5 hours |
6 hours |
|
104oF (40oC) |
75 minutes |
105 minutes |
|
140oF (60oC) |
26 minutes |
30 minutes |
|
212oF (100oC) |
6 minutes |
6 minutes |
STADARD TEST SPECIMENS 標準測試樣品
Unless otherwise stated, the figures given below were all determined by testing standard specimens made up by lap-jointing 4 x 1 x 0.06 inch strips of aluminum. The joint area was 0.5 x 1 inch in each case. 除非特別說明，以下數據均基于標準測試樣品而來，樣品為4 x 1 x 0.06英寸鋁條，粘結區域?yàn)?/span>0.5 x 1英寸。
LAP SHEAR STRENGTH (psi) 搭接剪切強度
Effects of cure time and temperature固化溫度的影響
|
Cure Cycle 固化循環 |
Test Values 測試值 |
|
7 days @ 77oF (25oC) |
2400 |
|
30 min @ 176oF (80oC) |
2600 |
LAP SHEAR STRENGTH (psi) 搭接剪切強度
Effect of Test Temperature (Load applied 10 minutes after specimens reach test temperature.)
測試溫度的影響（樣品達到測試溫度后保持10分鐘）
|
Curing temp固化條件 |
Test temp 測試溫度 |
Test Values 測試值 |
|
7 days @ 77oF (25oC) |
-40oF (-40oC) |
1900 |
|
-4oF (-20oC) |
2000 |
|
|
68oF (20oC) |
2400 |
|
|
104oF (40oC) |
2900 |
|
|
140oF (60oC) |
2500 |
|
|
176oF (70oC) |
2400 |
|
|
212oF (100oC) |
1900 |
|
|
248° F (120oC) |
1300 |
|
|
|
284° F (140oC) |
800 |
|
|
||
|
24 hrs @ 77oF (25oC) + 30 min @ 176°F (80°C) |
-40oF (-40oC) |
2400 |
|
-4oF (-20oC) |
2500 |
|
|
68oF (20oC) |
2600 |
|
|
104oF (40oC) |
2500 |
|
|
140oF (60oC) |
3000 |
|
|
176oF (70oC) |
2600 |
|
|
212oF (100oC) |
2100 |
|
|
248° F (120oC) |
1400 |
|
|
284° F (140oC) |
900 |
|
LAP SHEAR STRENGTH (psi) 搭接剪切強度
Effect of Immersion (Cure cycle 16 hours @ 104oF (40oC).Immersion for 90 days in media listed.) 侵蝕的影響（固化條件為16 hours @ 104oF (40oC)，在媒介中侵蝕90天）
|
Media 媒介 |
Test Value測試值 |
|
Standard - As prepared 標準樣品 |
2700 |
|
IMS 國際金相學會 |
2750 |
|
Gasoline 汽油 |
3200 |
|
Ethyl Acetate (30 days) 乙酸乙酯 |
3300 |
|
Acetic Acid 10% 乙酸 |
2300 |
|
Xylene 二甲苯 |
2650 |
|
Lubricating Oil - HD30 潤滑油 |
2300 |
|
Paraffin 石蠟 |
2600 |
|
Water @ 68°F (20°C) 水 |
2750 |
|
Water @ 194°F (90°C) 水 |
2000 |
LAP SHEAR STRENGTH (psi) 搭接剪切強度
Effect of Tropical Exposure濕熱影響 (104o (40oC)/92% R.H.)
|
Cure Cycle 固化條件 |
Exposure Time 暴露時間 |
Test Value測試值 |
|
16 hrs @ 104o (40oC) |
0 days |
2700 |
|
30 days |
3050 |
|
|
60 days |
3100 |
|
|
90 days |
2900 |
LAP SHEAR STRENGTH (psi) 搭接剪切強度
Effect of Heat Aging 熱老化的影響 (Cured 16 hours @ 104°F (40°C).
|
Aging Temperature |
Exposure Time 暴露時間 |
Test Value測試值 |
|
158 oF (70oC)
|
0 days |
2700 |
|
30 days |
2800 |
|
|
60 days |
2600 |
|
|
90 days |
3000 |
LAP SHEAR STRENGTH (psi) 搭接剪切強度
Tested on Metal Substrates 金屬基質測試(Cured 16 hours @ 104oF (40oC)
|
Metal 金屬 |
Substrate Thickness (mm) 基質厚度 |
Test Value測試值 |
|
Carbon Steel 碳鋼 |
1.0 |
2500 |
|
Stainless Steel 不銹鋼 |
1.0 |
3200 |
|
Galvanized Steel鍍鋅鋼 |
1.5 |
1300 |
|
Copper 紅銅 |
1.5 |
2300 |
|
Brass 黃銅 |
1.5 |
2300 |
SHELF LIFE儲存期: Provided this material is stored under the recommended storage conditions in their original containers, it will remain in useable condition for 3 year from date of shipping.
保證該產品在推薦的保存溫度下和原始包裝容器中，從發貨之日起，可具有3年的有效使用期。
聯系我們
咨詢電話：0769-33211411
郵箱：dgadpm@dgadpm.com
地址：廣東省東莞市寮步鎮雅景橫路3號1棟501室
粵工商備P191808003407 COPYRIGHT ?2018 版權所有 ? 東莞市愛的合成材料有限公司 技術支持：美橙互聯 后臺管理
